/********************************************************************
*
* Standard register and bit definitions for the Texas Instruments
* MSP430 microcontroller.
*
* This file supports assembler and C development for
* MSP430x20x1 devices.
*
* Texas Instruments, Version 1.2
*
* Rev. 1.0, Setup
* Rev. 1.1, Removed some TACCx2 definition on TA2 module
* Rev. 1.2, added definitions for Interrupt Vectors xxIV
*
********************************************************************/

#ifndef __msp430x20x1
#define __msp430x20x1

#ifdef __cplusplus
extern "C" {
#endif


/*----------------------------------------------------------------------------*/
/* PERIPHERAL FILE MAP                                                        */
/*----------------------------------------------------------------------------*/

/* External references resolved by a device-specific linker command file */
#define SFR_8BIT(address)   extern volatile unsigned char address
#define SFR_16BIT(address)  extern volatile unsigned int address


/************************************************************
* STANDARD BITS
************************************************************/

#define BIT0                   (0x0001)
#define BIT1                   (0x0002)
#define BIT2                   (0x0004)
#define BIT3                   (0x0008)
#define BIT4                   (0x0010)
#define BIT5                   (0x0020)
#define BIT6                   (0x0040)
#define BIT7                   (0x0080)
#define BIT8                   (0x0100)
#define BIT9                   (0x0200)
#define BITA                   (0x0400)
#define BITB                   (0x0800)
#define BITC                   (0x1000)
#define BITD                   (0x2000)
#define BITE                   (0x4000)
#define BITF                   (0x8000)

/************************************************************
* STATUS REGISTER BITS
************************************************************/

#define C                      (0x0001)
#define Z                      (0x0002)
#define N                      (0x0004)
#define V                      (0x0100)
#define GIE                    (0x0008)
#define CPUOFF                 (0x0010)
#define OSCOFF                 (0x0020)
#define SCG0                   (0x0040)
#define SCG1                   (0x0080)

/* Low Power Modes coded with Bits 4-7 in SR */

#ifdef __ASM_HEADER__ /* Begin #defines for assembler */
#define LPM0                   (CPUOFF)
#define LPM1                   (SCG0+CPUOFF)
#define LPM2                   (SCG1+CPUOFF)
#define LPM3                   (SCG1+SCG0+CPUOFF)
#define LPM4                   (SCG1+SCG0+OSCOFF+CPUOFF)
/* End #defines for assembler */

#else /* Begin #defines for C */
#define LPM0_bits              (CPUOFF)
#define LPM1_bits              (SCG0+CPUOFF)
#define LPM2_bits              (SCG1+CPUOFF)
#define LPM3_bits              (SCG1+SCG0+CPUOFF)
#define LPM4_bits              (SCG1+SCG0+OSCOFF+CPUOFF)

#include <In430.h>

#define LPM0         _bis_SR_register(LPM0_bits)         /* Enter Low Power Mode 0 */
#define LPM0_EXIT    _bic_SR_register_on_exit(LPM0_bits) /* Exit Low Power Mode 0 */
#define LPM1         _bis_SR_register(LPM1_bits)         /* Enter Low Power Mode 1 */
#define LPM1_EXIT    _bic_SR_register_on_exit(LPM1_bits) /* Exit Low Power Mode 1 */
#define LPM2         _bis_SR_register(LPM2_bits)         /* Enter Low Power Mode 2 */
#define LPM2_EXIT    _bic_SR_register_on_exit(LPM2_bits) /* Exit Low Power Mode 2 */
#define LPM3         _bis_SR_register(LPM3_bits)         /* Enter Low Power Mode 3 */
#define LPM3_EXIT    _bic_SR_register_on_exit(LPM3_bits) /* Exit Low Power Mode 3 */
#define LPM4         _bis_SR_register(LPM4_bits)         /* Enter Low Power Mode 4 */
#define LPM4_EXIT    _bic_SR_register_on_exit(LPM4_bits) /* Exit Low Power Mode 4 */
#endif /* End #defines for C */

/************************************************************
* PERIPHERAL FILE MAP
************************************************************/

/************************************************************
* SPECIAL FUNCTION REGISTER ADDRESSES + CONTROL BITS
************************************************************/

SFR_8BIT(IE1);                                /* Interrupt Enable 1 */
#define WDTIE                  (0x01)         /* Watchdog Interrupt Enable */
#define OFIE                   (0x02)         /* Osc. Fault  Interrupt Enable */
#define NMIIE                  (0x10)         /* NMI Interrupt Enable */
#define ACCVIE                 (0x20)         /* Flash Access Violation Interrupt Enable */

SFR_8BIT(IFG1);                               /* Interrupt Flag 1 */
#define WDTIFG                 (0x01)         /* Watchdog Interrupt Flag */
#define OFIFG                  (0x02)         /* Osc. Fault Interrupt Flag */
#define PORIFG                 (0x04)         /* Power On Interrupt Flag */
#define RSTIFG                 (0x08)         /* Reset Interrupt Flag */
#define NMIIFG                 (0x10)         /* NMI Interrupt Flag */

/************************************************************
* Basic Clock Module
************************************************************/
#define __MSP430_HAS_BC2__                    /* Definition to show that Module is available */

SFR_8BIT(DCOCTL);                             /* DCO Clock Frequency Control */
SFR_8BIT(BCSCTL1);                            /* Basic Clock System Control 1 */
SFR_8BIT(BCSCTL2);                            /* Basic Clock System Control 2 */
SFR_8BIT(BCSCTL3);                            /* Basic Clock System Control 3 */

#define MOD0                   (0x01)         /* Modulation Bit 0 */
#define MOD1                   (0x02)         /* Modulation Bit 1 */
#define MOD2                   (0x04)         /* Modulation Bit 2 */
#define MOD3                   (0x08)         /* Modulation Bit 3 */
#define MOD4                   (0x10)         /* Modulation Bit 4 */
#define DCO0                   (0x20)         /* DCO Select Bit 0 */
#define DCO1                   (0x40)         /* DCO Select Bit 1 */
#define DCO2                   (0x80)         /* DCO Select Bit 2 */

#define RSEL0                  (0x01)         /* Range Select Bit 0 */
#define RSEL1                  (0x02)         /* Range Select Bit 1 */
#define RSEL2                  (0x04)         /* Range Select Bit 2 */
#define RSEL3                  (0x08)         /* Range Select Bit 3 */
#define DIVA0                  (0x10)         /* ACLK Divider 0 */
#define DIVA1                  (0x20)         /* ACLK Divider 1 */
#define XTS                    (0x40)         /* LFXTCLK 0:Low Freq. / 1: High Freq. */
#define XT2OFF                 (0x80)         /* Enable XT2CLK */

#define DIVA_0                 (0x00)         /* ACLK Divider 0: /1 */
#define DIVA_1                 (0x10)         /* ACLK Divider 1: /2 */
#define DIVA_2                 (0x20)         /* ACLK Divider 2: /4 */
#define DIVA_3                 (0x30)         /* ACLK Divider 3: /8 */

#define DIVS0                  (0x02)         /* SMCLK Divider 0 */
#define DIVS1                  (0x04)         /* SMCLK Divider 1 */
#define SELS                   (0x08)         /* SMCLK Source Select 0:DCOCLK / 1:XT2CLK/LFXTCLK */
#define DIVM0                  (0x10)         /* MCLK Divider 0 */
#define DIVM1                  (0x20)         /* MCLK Divider 1 */
#define SELM0                  (0x40)         /* MCLK Source Select 0 */
#define SELM1                  (0x80)         /* MCLK Source Select 1 */

#define DIVS_0                 (0x00)         /* SMCLK Divider 0: /1 */
#define DIVS_1                 (0x02)         /* SMCLK Divider 1: /2 */
#define DIVS_2                 (0x04)         /* SMCLK Divider 2: /4 */
#define DIVS_3                 (0x06)         /* SMCLK Divider 3: /8 */

#define DIVM_0                 (0x00)         /* MCLK Divider 0: /1 */
#define DIVM_1                 (0x10)         /* MCLK Divider 1: /2 */
#define DIVM_2                 (0x20)         /* MCLK Divider 2: /4 */
#define DIVM_3                 (0x30)         /* MCLK Divider 3: /8 */

#define SELM_0                 (0x00)         /* MCLK Source Select 0: DCOCLK */
#define SELM_1                 (0x40)         /* MCLK Source Select 1: DCOCLK */
#define SELM_2                 (0x80)         /* MCLK Source Select 2: XT2CLK/LFXTCLK */
#define SELM_3                 (0xC0)         /* MCLK Source Select 3: LFXTCLK */
                                                                                   
#define LFXT1OF                (0x01)         /* Low/high Frequency Oscillator Fault Flag */
#define XT2OF                  (0x02)         /* High frequency oscillator 2 fault flag */
#define XCAP0                  (0x04)         /* XIN/XOUT Cap 0 */
#define XCAP1                  (0x08)         /* XIN/XOUT Cap 1 */
#define LFXT1S0                (0x10)         /* Mode 0 for LFXT1 (XTS = 0) */
#define LFXT1S1                (0x20)         /* Mode 1 for LFXT1 (XTS = 0) */
#define XT2S0                  (0x40)         /* Mode 0 for XT2 */
#define XT2S1                  (0x80)         /* Mode 1 for XT2 */

#define XCAP_0                 (0x00)         /* XIN/XOUT Cap : 0 pF */
#define XCAP_1                 (0x04)         /* XIN/XOUT Cap : 6 pF */
#define XCAP_2                 (0x08)         /* XIN/XOUT Cap : 10 pF */
#define XCAP_3                 (0x0C)         /* XIN/XOUT Cap : 12.5 pF */

#define LFXT1S_0               (0x00)         /* Mode 0 for LFXT1 : Normal operation */
#define LFXT1S_1               (0x10)         /* Mode 1 for LFXT1 : Reserved */
#define LFXT1S_2               (0x20)         /* Mode 2 for LFXT1 : VLO */
#define LFXT1S_3               (0x30)         /* Mode 3 for LFXT1 : Digital input signal */

#define XT2S_0                 (0x00)         /* Mode 0 for XT2 : 0.4 - 1 MHz */
#define XT2S_1                 (0x40)         /* Mode 1 for XT2 : 1 - 4 MHz */
#define XT2S_2                 (0x80)         /* Mode 2 for XT2 : 2 - 16 MHz */
#define XT2S_3                 (0xC0)         /* Mode 3 for XT2 : Digital input signal */

/************************************************************
* Comparator A
************************************************************/
#define __MSP430_HAS_CAPLUS__                 /* Definition to show that Module is available */

SFR_8BIT(CACTL1);                             /* Comparator A Control 1 */
SFR_8BIT(CACTL2);                             /* Comparator A Control 2 */
SFR_8BIT(CAPD);                               /* Comparator A Port Disable */

#define CAIFG                  (0x01)         /* Comp. A Interrupt Flag */
#define CAIE                   (0x02)         /* Comp. A Interrupt Enable */
#define CAIES                  (0x04)         /* Comp. A Int. Edge Select: 0:rising / 1:falling */
#define CAON                   (0x08)         /* Comp. A enable */
#define CAREF0                 (0x10)         /* Comp. A Internal Reference Select 0 */
#define CAREF1                 (0x20)         /* Comp. A Internal Reference Select 1 */
#define CARSEL                 (0x40)         /* Comp. A Internal Reference Enable */
#define CAEX                   (0x80)         /* Comp. A Exchange Inputs */

#define CAREF_0                (0x00)         /* Comp. A Int. Ref. Select 0 : Off */
#define CAREF_1                (0x10)         /* Comp. A Int. Ref. Select 1 : 0.25*Vcc */
#define CAREF_2                (0x20)         /* Comp. A Int. Ref. Select 2 : 0.5*Vcc */
#define CAREF_3                (0x30)         /* Comp. A Int. Ref. Select 3 : Vt*/

#define CAOUT                  (0x01)         /* Comp. A Output */
#define CAF                    (0x02)         /* Comp. A Enable Output Filter */
#define P2CA0                  (0x04)         /* Comp. A +Terminal Multiplexer */
#define P2CA1                  (0x08)         /* Comp. A -Terminal Multiplexer */
#define P2CA2                  (0x10)         /* Comp. A -Terminal Multiplexer */
#define P2CA3                  (0x20)         /* Comp. A -Terminal Multiplexer */
#define P2CA4                  (0x40)         /* Comp. A +Terminal Multiplexer */
#define CASHORT                (0x80)         /* Comp. A Short + and - Terminals */

#define CAPD0                  (0x01)         /* Comp. A Disable Input Buffer of Port Register .0 */
#define CAPD1                  (0x02)         /* Comp. A Disable Input Buffer of Port Register .1 */
#define CAPD2                  (0x04)         /* Comp. A Disable Input Buffer of Port Register .2 */
#define CAPD3                  (0x08)         /* Comp. A Disable Input Buffer of Port Register .3 */
#define CAPD4                  (0x10)         /* Comp. A Disable Input Buffer of Port Register .4 */
#define CAPD5                  (0x20)         /* Comp. A Disable Input Buffer of Port Register .5 */
#define CAPD6                  (0x40)         /* Comp. A Disable Input Buffer of Port Register .6 */
#define CAPD7                  (0x80)         /* Comp. A Disable Input Buffer of Port Register .7 */

/*************************************************************
* Flash Memory
*************************************************************/
#define __MSP430_HAS_FLASH2__                 /* Definition to show that Module is available */

SFR_16BIT(FCTL1);                             /* FLASH Control 1 */
SFR_16BIT(FCTL2);                             /* FLASH Control 2 */
SFR_16BIT(FCTL3);                             /* FLASH Control 3 */

#define FRKEY                  (0x9600)       /* Flash key returned by read */
#define FWKEY                  (0xA500)       /* Flash key for write */
#define FXKEY                  (0x3300)       /* for use with XOR instruction */

#define ERASE                  (0x0002)       /* Enable bit for Flash segment erase */
#define MERAS                  (0x0004)       /* Enable bit for Flash mass erase */
#define WRT                    (0x0040)       /* Enable bit for Flash write */
#define BLKWRT                 (0x0080)       /* Enable bit for Flash segment write */
#define SEGWRT                 (0x0080)       /* old definition */ /* Enable bit for Flash segment write */

#define FN0                    (0x0001)       /* Divide Flash clock by 1 to 64 using FN0 to FN5 according to: */
#define FN1                    (0x0002)       /*  32*FN5 + 16*FN4 + 8*FN3 + 4*FN2 + 2*FN1 + FN0 + 1 */
#ifndef FN2
#define FN2                    (0x0004)
#endif
#ifndef FN3
#define FN3                    (0x0008)
#endif
#ifndef FN4
#define FN4                    (0x0010)
#endif
#define FN5                    (0x0020)
#define FSSEL0                 (0x0040)       /* Flash clock select 0 */        /* to distinguish from USART SSELx */
#define FSSEL1                 (0x0080)       /* Flash clock select 1 */

#define FSSEL_0                (0x0000)       /* Flash clock select: 0 - ACLK */
#define FSSEL_1                (0x0040)       /* Flash clock select: 1 - MCLK */
#define FSSEL_2                (0x0080)       /* Flash clock select: 2 - SMCLK */
#define FSSEL_3                (0x00C0)       /* Flash clock select: 3 - SMCLK */

#define BUSY                   (0x0001)       /* Flash busy: 1 */
#define KEYV                   (0x0002)       /* Flash Key violation flag */
#define ACCVIFG                (0x0004)       /* Flash Access violation flag */
#define WAIT                   (0x0008)       /* Wait flag for segment write */
#define LOCK                   (0x0010)       /* Lock bit: 1 - Flash is locked (read only) */
#define EMEX                   (0x0020)       /* Flash Emergency Exit */
#define LOCKA                  (0x0040)       /* Segment A Lock bit: read = 1 - Segment is locked (read only) */
#define FAIL                   (0x0080)       /* Last Program or Erase failed */

/************************************************************
* DIGITAL I/O Port1/2 Pull up / Pull down Resistors
************************************************************/
#define __MSP430_HAS_PORT1_R__                /* Definition to show that Module is available */
#define __MSP430_HAS_PORT2_R__                /* Definition to show that Module is available */

SFR_8BIT(P1IN);                               /* Port 1 Input */
SFR_8BIT(P1OUT);                              /* Port 1 Output */
SFR_8BIT(P1DIR);                              /* Port 1 Direction */
SFR_8BIT(P1IFG);                              /* Port 1 Interrupt Flag */
SFR_8BIT(P1IES);                              /* Port 1 Interrupt Edge Select */
SFR_8BIT(P1IE);                               /* Port 1 Interrupt Enable */
SFR_8BIT(P1SEL);                              /* Port 1 Selection */
SFR_8BIT(P1REN);                              /* Port 1 Resistor Enable */

SFR_8BIT(P2IN);                               /* Port 2 Input */
SFR_8BIT(P2OUT);                              /* Port 2 Output */
SFR_8BIT(P2DIR);                              /* Port 2 Direction */
SFR_8BIT(P2IFG);                              /* Port 2 Interrupt Flag */
SFR_8BIT(P2IES);                              /* Port 2 Interrupt Edge Select */
SFR_8BIT(P2IE);                               /* Port 2 Interrupt Enable */
SFR_8BIT(P2SEL);                              /* Port 2 Selection */
SFR_8BIT(P2REN);                              /* Port 2 Resistor Enable */

/************************************************************
* Timer A2
************************************************************/
#define __MSP430_HAS_TA2__                    /* Definition to show that Module is available */

SFR_16BIT(TAIV);                              /* Timer A Interrupt Vector Word */
SFR_16BIT(TACTL);                             /* Timer A Control */
SFR_16BIT(TACCTL0);                           /* Timer A Capture/Compare Control 0 */
SFR_16BIT(TACCTL1);                           /* Timer A Capture/Compare Control 1 */
SFR_16BIT(TAR);                               /* Timer A */
SFR_16BIT(TACCR0);                            /* Timer A Capture/Compare 0 */
SFR_16BIT(TACCR1);                            /* Timer A Capture/Compare 1 */

/* Alternate register names */
#define CCTL0                  TACCTL0        /* Timer A Capture/Compare Control 0 */
#define CCTL1                  TACCTL1        /* Timer A Capture/Compare Control 1 */
#define CCR0                   TACCR0         /* Timer A Capture/Compare 0 */
#define CCR1                   TACCR1         /* Timer A Capture/Compare 1 */
#define CCTL0_                 TACCTL0_       /* Timer A Capture/Compare Control 0 */
#define CCTL1_                 TACCTL1_       /* Timer A Capture/Compare Control 1 */
#define CCR0_                  TACCR0_        /* Timer A Capture/Compare 0 */
#define CCR1_                  TACCR1_        /* Timer A Capture/Compare 1 */

#define TASSEL1                (0x0200)       /* Timer A clock source select 0 */
#define TASSEL0                (0x0100)       /* Timer A clock source select 1 */
#define ID1                    (0x0080)       /* Timer A clock input divider 1 */
#define ID0                    (0x0040)       /* Timer A clock input divider 0 */
#define MC1                    (0x0020)       /* Timer A mode control 1 */
#define MC0                    (0x0010)       /* Timer A mode control 0 */
#define TACLR                  (0x0004)       /* Timer A counter clear */
#define TAIE                   (0x0002)       /* Timer A counter interrupt enable */
#define TAIFG                  (0x0001)       /* Timer A counter interrupt flag */

#define MC_0                   (0*0x10u)      /* Timer A mode control: 0 - Stop */
#define MC_1                   (1*0x10u)      /* Timer A mode control: 1 - Up to CCR0 */
#define MC_2                   (2*0x10u)      /* Timer A mode control: 2 - Continous up */
#define MC_3                   (3*0x10u)      /* Timer A mode control: 3 - Up/Down */
#define ID_0                   (0*0x40u)      /* Timer A input divider: 0 - /1 */
#define ID_1                   (1*0x40u)      /* Timer A input divider: 1 - /2 */
#define ID_2                   (2*0x40u)      /* Timer A input divider: 2 - /4 */
#define ID_3                   (3*0x40u)      /* Timer A input divider: 3 - /8 */
#define TASSEL_0               (0*0x100u)     /* Timer A clock source select: 0 - TACLK */
#define TASSEL_1               (1*0x100u)     /* Timer A clock source select: 1 - ACLK  */
#define TASSEL_2               (2*0x100u)     /* Timer A clock source select: 2 - SMCLK */
#define TASSEL_3               (3*0x100u)     /* Timer A clock source select: 3 - INCLK */

#define CM1                    (0x8000)       /* Capture mode 1 */
#define CM0                    (0x4000)       /* Capture mode 0 */
#define CCIS1                  (0x2000)       /* Capture input select 1 */
#define CCIS0                  (0x1000)       /* Capture input select 0 */
#define SCS                    (0x0800)       /* Capture sychronize */
#define SCCI                   (0x0400)       /* Latched capture signal (read) */
#define CAP                    (0x0100)       /* Capture mode: 1 /Compare mode : 0 */
#define OUTMOD2                (0x0080)       /* Output mode 2 */
#define OUTMOD1                (0x0040)       /* Output mode 1 */
#define OUTMOD0                (0x0020)       /* Output mode 0 */
#define CCIE                   (0x0010)       /* Capture/compare interrupt enable */
#define CCI                    (0x0008)       /* Capture input signal (read) */
#define OUT                    (0x0004)       /* PWM Output signal if output mode 0 */
#define COV                    (0x0002)       /* Capture/compare overflow flag */
#define CCIFG                  (0x0001)       /* Capture/compare interrupt flag */

#define OUTMOD_0               (0*0x20u)      /* PWM output mode: 0 - output only */
#define OUTMOD_1               (1*0x20u)      /* PWM output mode: 1 - set */
#define OUTMOD_2               (2*0x20u)      /* PWM output mode: 2 - PWM toggle/reset */
#define OUTMOD_3               (3*0x20u)      /* PWM output mode: 3 - PWM set/reset */
#define OUTMOD_4               (4*0x20u)      /* PWM output mode: 4 - toggle */
#define OUTMOD_5               (5*0x20u)      /* PWM output mode: 5 - Reset */
#define OUTMOD_6               (6*0x20u)      /* PWM output mode: 6 - PWM toggle/set */
#define OUTMOD_7               (7*0x20u)      /* PWM output mode: 7 - PWM reset/set */
#define CCIS_0                 (0*0x1000u)    /* Capture input select: 0 - CCIxA */
#define CCIS_1                 (1*0x1000u)    /* Capture input select: 1 - CCIxB */
#define CCIS_2                 (2*0x1000u)    /* Capture input select: 2 - GND */
#define CCIS_3                 (3*0x1000u)    /* Capture input select: 3 - Vcc */
#define CM_0                   (0*0x4000u)    /* Capture mode: 0 - disabled */
#define CM_1                   (1*0x4000u)    /* Capture mode: 1 - pos. edge */
#define CM_2                   (2*0x4000u)    /* Capture mode: 1 - neg. edge */
#define CM_3                   (3*0x4000u)    /* Capture mode: 1 - both edges */

/* TA2IV Definitions */
#define TAIV_NONE              (0x0000)       /* No Interrupt pending */
#define TAIV_TACCR1            (0x0002)       /* TACCR1_CCIFG */
#define TAIV_2                 (0x0004)       /* Reserved */
#define TAIV_6                 (0x0006)       /* Reserved */
#define TAIV_8                 (0x0008)       /* Reserved */
#define TAIV_TAIFG             (0x000A)       /* TAIFG */

/************************************************************
* WATCHDOG TIMER
************************************************************/
#define __MSP430_HAS_WDT__                    /* Definition to show that Module is available */

SFR_16BIT(WDTCTL);                            /* Watchdog Timer Control */
/* The bit names have been prefixed with "WDT" */
#define WDTIS0                 (0x0001)
#define WDTIS1                 (0x0002)
#define WDTSSEL                (0x0004)
#define WDTCNTCL               (0x0008)
#define WDTTMSEL               (0x0010)
#define WDTNMI                 (0x0020)
#define WDTNMIES               (0x0040)
#define WDTHOLD                (0x0080)

#define WDTPW                  (0x5A00)

/* WDT-interval times [1ms] coded with Bits 0-2 */
/* WDT is clocked by fSMCLK (assumed 1MHz) */
#define WDT_MDLY_32         (WDTPW+WDTTMSEL+WDTCNTCL)                         /* 32ms interval (default) */
#define WDT_MDLY_8          (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS0)                  /* 8ms     " */
#define WDT_MDLY_0_5        (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS1)                  /* 0.5ms   " */
#define WDT_MDLY_0_064      (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS1+WDTIS0)           /* 0.064ms " */
/* WDT is clocked by fACLK (assumed 32KHz) */
#define WDT_ADLY_1000       (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL)                 /* 1000ms  " */
#define WDT_ADLY_250        (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS0)          /* 250ms   " */
#define WDT_ADLY_16         (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS1)          /* 16ms    " */
#define WDT_ADLY_1_9        (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS1+WDTIS0)   /* 1.9ms   " */
/* Watchdog mode -> reset after expired time */
/* WDT is clocked by fSMCLK (assumed 1MHz) */
#define WDT_MRST_32         (WDTPW+WDTCNTCL)                                  /* 32ms interval (default) */
#define WDT_MRST_8          (WDTPW+WDTCNTCL+WDTIS0)                           /* 8ms     " */
#define WDT_MRST_0_5        (WDTPW+WDTCNTCL+WDTIS1)                           /* 0.5ms   " */
#define WDT_MRST_0_064      (WDTPW+WDTCNTCL+WDTIS1+WDTIS0)                    /* 0.064ms " */
/* WDT is clocked by fACLK (assumed 32KHz) */
#define WDT_ARST_1000       (WDTPW+WDTCNTCL+WDTSSEL)                          /* 1000ms  " */
#define WDT_ARST_250        (WDTPW+WDTCNTCL+WDTSSEL+WDTIS0)                   /* 250ms   " */
#define WDT_ARST_16         (WDTPW+WDTCNTCL+WDTSSEL+WDTIS1)                   /* 16ms    " */
#define WDT_ARST_1_9        (WDTPW+WDTCNTCL+WDTSSEL+WDTIS1+WDTIS0)            /* 1.9ms   " */

/* INTERRUPT CONTROL */
/* These two bits are defined in the Special Function Registers */
/* #define WDTIE               0x01 */
/* #define WDTIFG              0x01 */

/************************************************************
* Calibration Data in Info Mem
************************************************************/

#ifndef __DisableCalData

SFR_8BIT(CALDCO_16MHZ);                       /* DCOCTL  Calibration Data for 16MHz */
SFR_8BIT(CALBC1_16MHZ);                       /* BCSCTL1 Calibration Data for 16MHz */
SFR_8BIT(CALDCO_12MHZ);                       /* DCOCTL  Calibration Data for 12MHz */
SFR_8BIT(CALBC1_12MHZ);                       /* BCSCTL1 Calibration Data for 12MHz */
SFR_8BIT(CALDCO_8MHZ);                        /* DCOCTL  Calibration Data for 8MHz */
SFR_8BIT(CALBC1_8MHZ);                        /* BCSCTL1 Calibration Data for 8MHz */
SFR_8BIT(CALDCO_1MHZ);                        /* DCOCTL  Calibration Data for 1MHz */
SFR_8BIT(CALBC1_1MHZ);                        /* BCSCTL1 Calibration Data for 1MHz */

#endif /* #ifndef __DisableCalData */

/************************************************************
* Interrupt Vectors (offset from 0xFFE0)
************************************************************/

#define VECTOR_NAME(name)       name##_ptr
#define EMIT_PRAGMA(x)          _Pragma(#x)
#define CREATE_VECTOR(name)     void (* const VECTOR_NAME(name))(void) = &name
#define PLACE_VECTOR(vector,section) EMIT_PRAGMA(DATA_SECTION(vector,section))
#define ISR_VECTOR(func,offset) CREATE_VECTOR(func); \
                                PLACE_VECTOR(VECTOR_NAME(func), offset)

#define PORT1_VECTOR            (2 * 1u)                     /* 0xFFE4 Port 1 */
/*#define PORT1_ISR(func)         ISR_VECTOR(func, ".int02")  */ /* 0xFFE4 Port 1 */ /* CCE V2 Style */
#define PORT2_VECTOR            (3 * 1u)                     /* 0xFFE6 Port 2 */
/*#define PORT2_ISR(func)         ISR_VECTOR(func, ".int03")  */ /* 0xFFE6 Port 2 */ /* CCE V2 Style */
#define TIMERA1_VECTOR          (8 * 1u)                     /* 0xFFF0 Timer A CC1-2, TA */
/*#define TIMERA1_ISR(func)       ISR_VECTOR(func, ".int08")  */ /* 0xFFF0 Timer A CC1-2, TA */ /* CCE V2 Style */
#define TIMERA0_VECTOR          (9 * 1u)                     /* 0xFFF2 Timer A CC0 */
/*#define TIMERA0_ISR(func)       ISR_VECTOR(func, ".int09")  */ /* 0xFFF2 Timer A CC0 */ /* CCE V2 Style */
#define WDT_VECTOR              (10 * 1u)                    /* 0xFFF4 Watchdog Timer */
/*#define WDT_ISR(func)           ISR_VECTOR(func, ".int10")  */ /* 0xFFF4 Watchdog Timer */ /* CCE V2 Style */
#define COMPARATORA_VECTOR      (11 * 1u)                    /* 0xFFF6 Comparator A */
/*#define COMPARATORA_ISR(func)   ISR_VECTOR(func, ".int11")  */ /* 0xFFF6 Comparator A */ /* CCE V2 Style */
#define NMI_VECTOR              (14 * 1u)                    /* 0xFFFC Non-maskable */
/*#define NMI_ISR(func)           ISR_VECTOR(func, ".int14")  */ /* 0xFFFC Non-maskable */ /* CCE V2 Style */
#define RESET_VECTOR            (15 * 1u)                    /* 0xFFFE Reset [Highest Priority] */
/*#define RESET_ISR(func)         ISR_VECTOR(func, ".int15")  */ /* 0xFFFE Reset [Highest Priority] */ /* CCE V2 Style */

/************************************************************
* End of Modules
************************************************************/

#ifdef __cplusplus
}
#endif /* extern "C" */

#endif /* #ifndef __msp430x20x1 */